BT-PON ONU BT-7xxXR/BT-3xxXR Web Configuration Guide

This guidance document is applicable to BT-7xxXR/BT-3xxXR series models ONU equipment of BT-PON.

1.Web Login #

Login URL：http://192.168.1.1
user login account：useradmin ; password：123456
After entering the username and password correctly, click Login button to enter the web management interface.

2.ONU Status #

login successfully enter the Web page look over Device Status
Device Status:

PON Status:
View TX, RX information:

WAN connections Status:

WLAN Configuration:

CATV Status:

3.WAN Connection Create #

To set up the WAN Connection, you need to log into the ONU administration page with a super administration account. Create multiple WAN connections (PPPOE, TR069 (DHCP), VOIP (DHCP), IPTV):

3.1 Create PPPOE WAN connection configuration #

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(PPPoE internet VLAN ID)
Channel Mode: PPPoE
Connection Type: INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
UserName: PPPoE AUthorized Username.
Password: PPPoE Authorized Password.
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5.8g wifi )
WLAN1( WLAN1 is 2.4g wifi )
Click the Apply Changes button (Save the configuration)

3.2 Create DHCP WAN connection configuration #

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select

VLAN ID: select (PPPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5.8g wifi)
WLAN1( WLAN1 is 2.4g wifi)
Click the Apply Changes button (Save the configuration)

3.3 Create TR069 WAN connection and TR069 configuration #

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(PPPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: TR069 or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
No need to ping ports
Click the Apply Changes button (Save the configuration)
Enter the Admin
TR-069: Select
URL: http://192.168.88.250:80/acs
Click the Apply button (Save the configuration)

3.4 Create VoIP WAN and VoIP configuration #

Create a VoIP WAN connection :
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(IPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: VOICE selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5 g internet)
WLAN1( WLAN1 is 2.4 g internet)
Enter: Apply Changes (Save the configuration)

Enter the VOIP
Viop line 1: select
Display Name:
Number:
Login ID:
Password:
Proxy: select enable
Proxy Addr: Proxy server address
Apply: select

3.5 Create IPTV WAN Connection and IPTV configuration #

Create a IPTV WAN connection:
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(IPoE internet VLAN ID)
Channel Mode: Bridged
Connection Type: Other selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
LAN PORT Binding: select LAN2(IPTV PORT)
Enter: Apply Changes (Save the configuration)
Enter the Admin
Multicast Vlan: select
Select the newly created IPTV WAN connection.Select modify under the corresponding WAN connection.Select modified prompt to set multicast VLAN
Setup Multicast Vlan:IPTV VLAN ID
Apply: select

3.6 Create IPTV WAN Connection and IPTV configuration #

Create a IPTV WAN connection:
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select( internet VLAN ID)
Channel Mode: IPoE
Connection Type: INTERNET selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
LAN PORT Binding: select LAN2(IPTV PORT)
Enter: Apply Changes (Save the configuration)
Enter the Admin
Multicast Vlan: select
Select the newly created IPTV WAN connection. Select modify under the corresponding WAN connection. Select modified prompt to set multicast VLAN
Setup Multicast Vlan: IPTV VLAN ID
Apply: select

4.LAN interface configuration #

4.1 LAN IP Setting #

Enter the LAN: LAN interface modification LAN_IP address configuration:
LAN:Select(LAN interface settings)
IP Address: 192.168.xxx.xxx
Subnet Mask: 255.255.255.0
IP Version: IPV4/IPV6
Click the APPLY button
The reboot will not take effect until the IP is set

4.2 Modify LAN IP Address Pool #

Modify LAN IP address pool configuration:
Enter the LAN: LAN interface modification
LAN: Select(LAN interface settings)
IPV4: Select
IP Pool Range: 192.168.xxx.2——192.168.xxx.254(Start Addres – End Address)
Subnet Mask: 255.255.255.0
Gateway Address: 192.168.xxx.xxx
Click the Apply Changes button

5. 5g WIFI Configuration #

5.1 5g WIFI SSID Configuration Modify WIFI SSIDConfiguration: #

Enter the WLAN
Basic Settings: Select
SSID: Modifiable.
Click the Apply Changes button
Close the 5g wireless

Modify wireless mode adn Channel Width,CHannel Number.

To modify the wireless channel, the default is auto. If you can’t find a wireless signal on your phone, change the value of the wireless channel to 149 and try again.

To modify the 5g wireless SSID and password
Enter the WLAN
Security: Select
Pre-Shared Key: Modifiable.
Click the Apply Changes button

6. 2.4g WIFI Configuration #

6.1 2.4g WIFI SSID, wireless mode adn Channel Width,Channel Number.Configuration #

Enter the WLAN
WLAN1(2.4GHz)
Basic Settings: Select
SSID.wireless mode. Channel Width. CHannel Number :Modifiable.
Click the Apply Changes button
To modify the wireless channel, the default is auto. If you can’t find a wireless signal on your phone, change the value of the wireless channel to 1 and try again

Close the 2.4g wireless

To modify the 2.4g wireless SSID and password
Enter the WLAN
WLAN1(2.4GHz)
Security: Select
Pre-Shared Key: Modifiable.
Click the Apply Changes button

7.Turn on and off the CATV interface functions #

Enter the Admin
CATV Confinguration: select
Enable CATV: Select
Click the Apply button

8. Enable remote access ONU to manage web pages.(that is, open access to the HTTP port of the wan interface) #

Enter the Admin
ACL: select
Interface: WAN
HTTP: select
Click the Update button

9. SoftWare Upgrade #

WEB page upgrade guide
WEB page upgrade configuration:
Enter the Admin
Firmware Upgrade: select
Click Select the file button: Select the file you want to upgrade
Click Upgraed button
click the “Select the file” button, select the suffix name. bin upgrade file, and then click the Upgrade button. Wait 3-4 minutes, the device will restart automatically after the upgrade is completed.